ABSTRACT

Unmanned Aerial Vehicles (UAVs) have become increasingly popular in recent years for agricultural research. High spatial and temporal resolution images obtained with UAVs are ideal for many applications in agriculture. The objective of this study was to evaluate the performance of vegetation indices (VIs) derived from UAV images for quantification of plant nitrogen (N) concentration of spring wheat, a major cereal crop worldwide. This study was conducted at three locations in Idaho, United States. A quadcopter UAV equipped with a red edge multispectral sensor was used to collect images during the 2016 growing season. Flight missions were successfully carried out at Feekes 5 and Feekes 10 growth stages of spring wheat. Plant samples were collected on the same days as UAV image data acquisition and were transferred to lab for N concentration analysis. Different VIs including Normalized Difference Vegetative Index (NDVI), Red Edge Normalized Difference Vegetation Index (NDVI_{red edge}), Enhanced Vegetation Index 2 (EVI₂), Red Edge Simple Ratio (SR_{red edge}), Green Chlorophyll Index (CI_green), Red Edge Chlorophyll Index (CI_{red edge}), Medium Resolution Imaging Spectrometer (MERIS) Terrestrial Chlorophyll Index (MTCI) and Red Edge Triangular Vegetation Index (core only) (RTVI_core) were calculated for each flight event. At Feekes 5 growth stage, red edge and green based VIs showed higher correlation with plant N concentration compare to the red based VIs. At Feekes 10 growth stage, all calculated VIs showed high correlation with plant N concentration. Empirical relationships between VIs and plant N concentration were cross validated using test data sets for each growth stage. At Feekes 5, the plant N concentration estimated based on NDVI_{red edge} showed one to one correlation with measured N concentration. At Feekes 10, the estimated and measured N concentration were highly correlated for all empirical models, but the model based on CI_green was the only model that had a one to one correlation between estimated and measured plant N concentration. The observed high correlations between VIs derived from UAV and the plant N concentration suggests the significance of VIs deriving from UAVs for within-season N concentration monitoring of agricultural crops such as spring wheat.

Keywords:

Unmanned Aerial Vehicles and Systems (UAV), Vegetation Indices (VIs), Plant Nitrogen Concentration

1. Introduction

Nitrogen (N) is one of the essential factors for crop production in terms of plant growth and development and crop quality [1] [2]. Adequate supply of N is fundamental for optimizing wheat (Triticum aestivum L.) yield and grain quality [3] [4]. Nitrogen regulates plant growth processes and plays a vital role in chlorophyll (CL) production―the basis for the photosynthesis process [5]. Insufficient N supply can negatively affect photosynthesis process and result in crop yield and quality penalties [3]. On the other hand, excessive N application to agricultural crops has been associated with nitrate leaching, soil denitrification, ammonia volatilization, and nitrous oxide contamination of aquifers and aggravating the climate change [6] [7]. Dynamic and efficient fertilization (appropriate time and rate) is very important for optimizing crop yield and maintaining environmental quality [8]. Accurate estimation of crop N concentration is vital for developing effective fertilizer-N recommendations.

There is a strong correlation between N concentration and CL content at foliar and canopy scale because most of leaf N is localized within the CL molecules [9] [10] [11] [12]. Chlorophyll content is the main elements that govern the crop reflectance in the visible (VIS) and near infrared (NIR) regions of spectrum [8]. Thus, vegetation reflectance in these parts of spectrum is closely associated with N concentration. Remote sensing enables to acquire crop reflectance and provide diagnostic information on crop N concentration quickly and in a spatial context, compared to traditional destructive sampling techniques [13]. During the last few decades, scientists have proposed several vegetation indices (VIs) calculated from reflectance data to assess CL content and N concentration [8] [13] [14] [15]. These VIs are mostly a combination of NIR and VIS spectral bands, representing radiation scattering by canopy and radiation absorption by CL respectively [16]. Although these VIs accurately estimate CL and N concentration early in the growing season at lower CL values, they become less sensitive as the red spectral band is strongly absorbed by CL. Gitelson and Merzlyak [17] showed that red edge region is sensitive to a wide range of CL content values, and the use of this part of spectrum in VIs calculation can reduce the saturation effect due to lower absorption of the red edge region by CL. Several VIs based on this spectral region have been developed and used successfully to estimate CL and N concentration.

Gitelson and Merzlyak [17] replaced the red spectral band (675 nm) with red edge spectral band (705 nm) in Normalized Difference Vegetation Index (NDVI) and developed a new index called Red Edge Normalized Difference Vegetation Index (NDVI_{red edge}). They showed that traditional NDVI had a tendency to become saturated at higher CL level of senescing maple and chestnut leaves while NDVI_{red edge} continued to show strong linear correlation with CL content and observed no saturation issue. In a similar study, Gitelson et al. [18] showed that reciprocal of red edge spectral band is closely related to the CL content in leaves of all species. They proposed Red Edge Chlorophyll Index (CI_{red edge}) and showed that CI_{red edge} is highly correlated with CL content (coefficient of determination R² > 0.94). In another study, Dash and Curran [19] developed MERIS Terrestrial Chlorophyll Index (MTCI). They used data in three red/NIR wavebands centered at 681.25, 708.75 and 753.75 nm (bands 8, 9 and 10 in the MERIS standard band setting) to develop MTCI. They determined the relationship between MTCI and CL content using actual CL content for sites in the New Forest, United Kingdom (UK) and for small plots in a greenhouse experiment. Their results showed that MTCI is strongly and positively correlated to actual CL content. Li et al. [5] evaluated red edge based spectral indices for estimating plant N concentration and uptake of maize (Zea mays L.). They calculated chlorophyll content index (CCCI), NDVI_{red edge}, CI_{red edge} and MTCI from hyperspectral narrow bands, simulated Crop Circle ACS-470 active crop canopy sensor bands and simulated WorldView-2 satellite broad bands. Their results showed that there is a positive strong correlation between red edge based VIs and N concentration in maize. Their results also indicated that CCCI performed the best across different bandwidths for estimating maize plant N concentration at the V6 and V7 and V10 - V12 stages. In another study, Wang et al. [20] compared broad-band and red edge based spectral VIs to estimate N concentration in corn, wheat, rice (Oryza sativa L.) and soybeans (Glycine max L.). They calculated various VIs from images acquired by the Compact Airborne Spectrographic Imager (CASI) sensor. Their result showed that NDVI performed the best compared to other VIs, and red edge based VIs did not show potential for accurate estimation of leaf N concentration data due to spectral resolution.

Unmanned aerial vehicles (UAVs) are remote sensing systems that can capture crop reflectance in the VIS-NIR region of spectrum and assess CL and N concentration. The UAVs, which have recently gained tractions in number of studies, acquire ultra-high spatial resolution images by flying at low altitudes [21] [22]. Operational advantages such as low-cost systems, high flexibility in terms of flight planning and acquisition scheduling, and imaging below cloud cover make UAVs an appropriate tool to study crop biophysical parameters including N concentration [23]. In a few studies, scientists have used reflectance data derived from UAVs to estimate CL or N concentration. Lu et al. [24] mounted a Mini Multi-Camera Array (Mini-MCA) imaging system on an octocopter UAV to estimate rice N status. They examined various VIs to estimate N concentration at panicle initiation and stem elongation growth stages in rice. Their results showed that MTCI was best for estimating rice N concentration with R² = 0.48. In another study, Caturegli et al. [25] compared the spectral reflectance of three turfgrasses (Cynodon dactylon × transvaalensis (Cdxt) “Patriot”, Zoysia matrella (Zm) “Zeon” and Paspalum vaginatum (Pv) “Salam”) acquired with a UAV and using a ground based instrument. They also tested the sensitivity of the two data acquisition sources in detecting induced variation among N application levels and for NDVI calculation. Their results showed that NDVI obtained with the ground based sensor was highly correlated with UAV based NDVI, with correlation coefficient values ranging from 0.83 to 0.97. They also showed that UAV based NDVI was strongly correlated with N measured in the clipped plant biomass samples (correlation coefficient of 0.95). Similarly, Hunt et al. [26] used a UAV to monitor N status of irrigated potato (Solanum tuberosum L.). They used a small parafoil-wing UAV to acquire color-infrared images. They showed that each of applied N treatments could be precisely distinguished in the images. Their results also concluded that NDVI and Green Normalized Difference Vegetation Index (GNDVI) were not useful for in-season N management in potato because the above-ground changes in leaf CL were not sufficiently large to be detected by remote sensing early in the growing season.

So far, very few studies have investigated the potential of using red edge based VIs from the UAV data for canopy CL or N concentration estimation. To date, no studies on comparing red edge based VIs from the UAV data for wheat canopy CL or N concentration estimation have been reported. The main goal of this study was to evaluate the performance of UAV based VIs in estimating plant N concentration at canopy scale. Specifically, we analyzed and statistically compared the performance of different red edge based VIs from UAV data to estimate spring wheat plant N concentration.

2. Materials and Methods

2.1. Study Area

The experimental studies were conducted at five different locations in Idaho during 2016 growing season (Table 1 and Figure 1). The soil type, mean annual temperature, and mean annual precipitation for each study site are presented in Table 1.

Hard red spring wheat (cv. Cabernet) was planted using a Hege 500 series drill

at Rupert and Ashton, and soft white spring wheat (cv. Alturas) was planted at Parma using H&N Equipment research plot drill, at a density of approximately 106.5 kg seeds ha⁻¹. Row spacing was set at 17.78 cm using double disk openers. The plots were 1.52 wide by 4.27 m long, and then reduced to 3.05 m using glyphosate and tillage. Granular urea (46-0-0) was surface broadcasted immediately after planting at five different rates (0, 84, 168, 252, and 336 kg N ha⁻¹). Each treatment was replicated four times in a randomized complete block design, resulting in a total of 20 plots at each location. Spring planting conditions were good for crop establishment. Soil moisture March through April were above average, which resulted in excellent early season growth and development. Early season precipitation provided excellent growing conditions until irrigation became available in April when all sites were irrigated every 7 to 10 days using sprinkle irrigation systems. Timely planting dates resulted in excellent tillering and a long growing period.

2.2. Unmanned Aerial System

A quadcopter UAV 3DR Solo (3D Robotics, Inc., Berkeley, CA) shown in Figure 2 was selected to carry camera payloads to acquire ultra-high-resolution imagery. Solo is powered by four electric brushless 880 kV motors, two that spin clockwise, and two counterclockwise. Solo’s arms are labeled 1 to 4 on the ends of the arms. Motors on arms #1 and #2 spin counterclockwise and use clockwise-tightening propellers with silver tops. Conversely, motors on arms #3 and #4 spin clockwise and use counter-clockwise tightening propellers with black tops. Solo’s onboard computers control navigation, attitude, and communications in flight while sending real-time telemetry and video output and receiving control inputs over the 3DR Link secure WiFi network. A 14.8v dc 5200 mAh lithium polymer (LiPo) rechargeable battery is located next to the power button. The intelligent battery systems on the Solo tracks battery power and informs the pilot when the battery needs to be recharged. Solo includes a GoPro^® the Frame (GoPro, Inc, San Mateo, CA) fixed mount to support a GoPro^® HERO camera (GoPro, Inc, San Mateo, CA). Alternatively, the fixed mount could be replaced by the optional 3-Axis Gimbal (3D Robotics, Inc, Berkeley, CA) (Figure 2). Empty weight of the quadcopter is 1.74 kg and weight increased to 1.9 kg with compatible camera and Solo Gimbal.

A MicaSense Red Edge™ 3 Multispectral Camera (MicaSense, Inc, Seattle, WA) with an integrated Global Positioning System (GPS) with an accuracy of 2 - 3 meters, mounted on the UAV was used to obtain the imagery. The camera was mounted on a Gimbal and as the camera’s weight was similar to GoPro camera’s weight, there was no need to add balance weight. The camera acquires 1.3-megapixel images in five spectral bands (red edge, near infrared, red, green, and blue) with 12-bit Digital Negative (DNG) or 16-bit Tag Image File Format (TIFF) radiometric resolution. The ground spatial resolution of resulting images from the narrowband imager is 8 cm (per band) at 120 m above ground level. The MicaSense Red Edge™ 3 has a Downwelling Light Sensor (DLS) (MicaSense,

Inc, Seattle, WA), which measures the ambient light during a flight for each of the five bands and records this information in the metadata of the images captured by the camera. The gain and exposure settings are automatically optimized for each capture and each band to prevent blurring or over-exposure, which results in properly exposed images.

2.3. Multispectral Image Acquisition and Processing

The UAV images were captured within 2.0 hours of solar noon with flight duration ranging from 15 to 20 minutes in sunny and cloud free conditions. Mission planer software [27] was used to design the flight path and choose the flight and sensor parameters to ensure there is an adequate overlap between acquired images for mosaicking. Two flight missions performed at each location to coincide with Feekes 5 and Feekes 10 spring wheat growth stages resulted in six flight missions per season. These growth stages were chosen because N fertilizer applied at these growth stages has potential to maximize grain yield and quality.

Acquired multispectral images were imported to Micasense Atlas software (MicaSense, Inc, Seattle, WA) for mosaicking, georeferencing and radiometric calibration. Micasense Atlas has a partnership with Pix4D mapper image analysis software (Pix4D SA, Lausanne, Switzerland) to create aligned, mosaicked and georeferenced images from multispectral data captured with the MicaSense red edge camera. The Pix4D finds hundreds of tie-points between overlapped images and stiches the individual images together to build one ortho-rectified image of the whole study area. The accuracy of an outputted reconstructed images are usually 1-2 times the ground spatial resolution. In this study, we had different treatments in the adjacent rows (100 cm row spacing) (well separated plots), so a low level of mosaicking error is allowable when using UAV images for our purpose [28]. Then, the mosaicked images were radiometrically calibrated using the Red Edge Camera Radiometric Calibration Model in Atlas software. Atlas software uses the calibration curve associated with a Calibrated Reflectance Panel (CRP) to perform calibration model and convert the raw pixel values of an image into absolute spectral radiance values. The CRP was placed adjacent to the study area during each flight mission, and an image of the CRP was captured immediately before and immediately after each flight. The output of radiometric calibration model is a 5-layer, 16-bit ortho-rectified GeoTIFF image.

2.4. Field Sampling and Measurements

To obtain a representative plant sample, aboveground biomass was destructively sampled at Feekes 5 and Feekes 10 growth stages by cutting three randomly selected plants in the middle of each plot immediately after each UAV flight event. Plant samples were dried in the oven for 72 hours at 80˚c and then were transferred to the lab for N content analysis. Samples’ N content analysis was performed using the AOAC method 990.3 [29] at Brookside Laboratories, Inc (New Bremen, OH, USA) with extended uncertainty of ±5%.

2.5. Vegetation Indices

The UAV reflectance data were used for calculating eight VIs, many of which have been proposed as surrogates for canopy N concentration estimation. The VIs tested include the Normalized Difference Vegetation Index, NDVI [30] , the Red Edge Normalized Difference Vegetation Index, NDVI_{red edge} [17] , the Enhanced Vegetation Index 2, EVI2 [31] , the Red Edge Simple Ratio, SR_{red edge} [32] , the Green and Red Edge Chlorophyll Indices, CI_green and CI_{red edge}, respectively [18] , the MERIS Terrestrial Chlorophyll Index, MTCI [19] , and the Core Red Edge Triangular Vegetation Index (RTVI_core) [33] (Table 2). For each study plot, a region of interest (ROI) was manually established by choosing the central two rows and mean of each VI value corresponding to that plot was extracted.

2.6. Statistical Analysis

The study plots were randomly divided into test and training data sets. For the training data sets, simple regression analysis was performed to find the best relationship fit between N concentration and each UAV based VI. The determination coefficient (R²) and Root Mean Squared Error (RMSE) were used to evaluate the predictive accuracy of each model. These parameters are widely used to evaluate the performance of empirical models. The RMSE are computed as shown in Equations (1):

$RMSE=\sqrt{\left[\frac{{{\sum }_{i=1}^M\left({\widehat{y}}_i-y_i\right)}^2}{M}\right]}$ (1)

where, ${\widehat{y}}_i$ is predicted value of N concentration; $y_i$ is measured N concentration, and M is total number of observations. In the next step, the test data set was used to evaluate the performance of developed model in the previous step. Predicted values of N concentration were plotted versus corresponding values of N concentration measured in the lab. The performance of regression models in estimating N for the training data set were evaluated by calculating the R² and

RMSE. In addition, Student’s t-tests were used to determine if the slope and the intercept of the regressions were significantly different from 1 and 0, respectively. If the values of slopes were not significantly different from 1 and the values of intercepts were not significantly different from 0, then it was concluded that the regression was not significantly different from the 1:1 line, and the empirical model could accurately predict N concentration.

3. Results and Discussions

3.1. Variation of Plant N Concentration

Based on different N application rates, a wide range of N concentration (%) ranged from 0.76% to 1.58% were obtained at Feekes 5 (Table 3). In Parma and Rupert sites, the highest N concentration (%) were obtained at fertilizer N rate of 336 kg N ha⁻¹ while in Ashton site, the highest N concentration (%) was obtained at fertilizer N rate of 252 kg N ha⁻¹. Similarly, at Feekes 10 a wide range of N concentration (%) ranged from 0.33% to 0.70% were obtained. In all sites, the highest N concentration (%) were obtained at fertilizer N rate of 336 kg N ha⁻¹. Generally, observed variations in N concentration were due to differences in climate, inherent soil fertility, and N rate applications. When comparing N fertilizer rate applications, in Parma and Rupert sites at both Feekes 5 and Feekes 10 growth stages, the rate of N fertilizer significantly affected N concentration. In Ashton site at Feekes 5, the rate of N fertilizer did not make significant changes in N concentration while at Feekes 10, the rate of N fertilizer made significant changes in N concentration.

Across growth stages, applied N rates and locations, plant N concentration decreased at all locations (Table 3 and Table 4). These results indicate the “dilution effect” as the crop matured, as described in previous studies [34] [35]. Plant N concentration was lower for Ashton site at both Feekes 5 and Feekes 10 growth stages, compared to other sites. As all study sites were irrigated and had similar soil type (silt loam), the differences between plant N concentration for the same N application rates may be associated with differences in the amount of plant available water. Ashton site received 15 cm more precipitation compared

Means within each column followed by the same letter are not significantly different at p < 0.01, as determined by the Duncan’s multiple range test.

Means within each column followed by the same letter are not significantly different at p < 0.01, as determined by the Duncan’s multiple range test.

to Rupert, and 17 cm more than Parma. The similar result was obtained for the semiarid grassland by Lu [36]. In that study, Lu showed that water additions significantly interacted to affect plant N uptake and N concentrations at the community level.

3.2. Plant N Concentration Models Development and Validation

We used the training data set for establishing separate plant N content predictive models using UAV based VIs for Feekes 5 and Feekes 10 separately. The training data set includes a wide range of plant N content values due to differences in N application rates. Eight models were developed using the vegetation indices NDVI, NDVI_{red edge}, EVI2, SR_{red edge}, MTCI, CI_green, CI_{red edge} and RTVI_core. Figure 3 and Figure 4 show the best relationship fit between N concentration and each UAV based VI for Feekes 5 and Feekes 10, respectively. At Feekes 5 (Figure 3), the R² of these models ranged from 0.69 to 0.88 and RMSE ranged from 0.096 to 0.16. At this growth stage, the highest R² between VIs and N concentrations was obtained for the CI_green. Also, the developed model based on this index showed the lowest RMSE with N concentration. The best relationship fit between N concentration and most VIs at Feekes 5 were quadratic (Figure 3). CI_green and MTCI were the only VIs which their best relationship fit with N concentration were linear. At Feekes 10 (Figure 4), the R² of the developed models ranged from 0.82 to 0.88 and RMSE ranged from 0.06 to 0.08. At this growth stage, the largest R² between VIs and N concentrations again was obtained for CI_green while the developed model based on NDVI_{red edge} had the lowest RMSE with N concentration. The best relationship fit between N concentration and all VIs (except EVI₂) at Feekes 10 were quadratic (Figure 4). EVI₂ was the only VIs for which its’ best relationship fit with N concentration was linear.

All UAV based VIs used in this study showed strong positive correlations with N concentration. In other words, all UAV based VIs used in this study were good indicators of spring wheat plant N concentration for both Feekes 5 and Feekes 10 growth stages. At Feekes 5 (Figure 3), red radiation based UAV indices (NDVI and EVI2) had lower R² and higher RMSE as compared with other green and red edge based UAV indices. At this stage (lower fractional vegetation

cover), soil background influence on research plots’ reflectance could be strong and could negatively affect the red based VIs accuracy [37]. Red edge based VIs could minimize the soil reflectance and isolate crop signal from soil reflectance as a function of canopy cover changes [13]. This suggests that applying red edge based or green based VIs from UAVs data can improve plant N concentration prediction compared to the red based UAV VIs at Feekes 5 of wheat growth stage. At this stage, CI_green showed the highest R² and lowest RMSE which suggests that the green based VIs can be a better indicator of plant N concentration than the red edge based VIs. This result is in consistent with the result of the previous study conducted by Li [38] who showed that red edge based VIs were more effective for N estimation at earlier growth stage of wheat. In addition, CI_green showed linear relationship with plant N concentration, which means sensitivity of the model did not change due to the wide range of variation in plant N concentration; it is straightforward to invert them between CI_green and plant N concentration to obtain a synoptic measure of N concentration. All the red edge based VIs showed comparable performance with similar R² and RMSE values at Feekes 5. At Feekes 10 growth stage (Figure 4), all UAV based VIs used in the study performed very well with similar R² and RMSE values. At this stage, the performance of NDVI and EVI2 for plant N concentration improved. All other UAV based VIs had similar performance compare to Feekes 5. Similar results have been reported by previous studies as well [38]. At Feekes 10, the crop canopy had fully developed, and soil background effect on research plots’ reflectance had been reduced, so red based and red edge based VIs showed similar performance.

The performance of the developed models in the previous step were evaluated using test data set for Feekes 5 and Feekes 10, separately. For this purpose, we used the developed models in previous step to estimate the N concentration. Table 5 and Table 6 show the results of comparison between measured N concentration and predicted N concentration retrieved from developed model in previous step for Feeks 5 and Feekes 10, respectively. At Feekes 5 (Table 5), the R² of the relationship between measured and predicted N concentration ranged from 0.67 to 0.84 and RMSE ranged from 0.147 to 0.196. At this growth stage, the lowest RMSE between measured and predicted N concentrations were obtained using the developed models based on RTVI_core and NDVI_{red edge} (Table 5). At this growth stage, all the developed models performed similar in terms of R² (Table 5). The results of a Student’s t test showed that for the developed models based on NDVI_{red edge}, SR_{red edge} and CI_{red edge} the slopes of those regression lines were not significantly different from 1 (t = 0.0279; t = 0.43947; t = 0.43706 respectively) (Table 7), while a similar test showed that the intercepts of those lines were not significantly different from 0 (t = 1.026; t = 0.730; t = 0.731, respectively) (Table 7). Thus, one could conclude that these regression lines were not significantly different from the 1:1 line. These results indicated that the developed model based on NDVI_{red edge} can predict the plant N concentration at Feekes 5 with best accuracy compared to other developed models (Figure 4(a)).

All t values were determined at 46 df and α = 0.05.

Similarly, at Feekes 10, the R² of the relationship between measured and predicted N concentration ranged from 0.72 to 0.73 and RMSE ranged from 0.09 to 0.104. At this growth stage, the lowest RMSE between measured and predicted N concentrations were obtained using the developed models based on CI_green and MTCI (Table 6). At this stage, all developed models had weaker performance in term of R², but all models had smaller RMSE compared to Feekes 5. The results of a Student’s t test showed that only for the model developed based on CI_green, the slope of the regression line was not significantly different from 1 (t = −1.15722, 46 df, α = 0.05) (Table 8), while a similar test showed that the intercept of that line was not significantly different from 0 (t = 0.6554, 46 df, α = 0.05) (Table 8). Thus, one could conclude this regression line was not significantly different from the 1:1 line. These results indicate that the model developed based on CI_green can predict the plant N concentration at Feekes 10 with greatest accuracy compared to other models, and can be successfully used to estimate plant N concentration of wheat crop in the future (Figure 4(b)).

In cross-validation process, results showed that at Feekes 5 developed model based on NDVI_{red edge} can predict the plant N concentration with best accuracy compared to other developed models. The developed model based on NDVI_{red edge} slightly underestimated the plant N concentration at lower values while overestimated the plant N concentration at higher values (Figure 5(a)). One possible reason for this is the soil type that was slightly different for each study site; it is possible that the total canopy reflectance was affected by slightly different background reflectance values at each location [39]. At Feekes 10, the developed model based on CI_green predicted the plant N concentration with highest accuracy compared to other models. The developed model based on CI_green at this growth stage did not have over- or underestimation issue as the crop canopy had been fully developed, which minimized the effect of different background reflectance soil values (Figure 5(b)).

At different growth stages, UAV based VIs showed different behaviors for

All t values were determined at 46 df and α = 0.05.

estimating plant N concentration. Therefore, growth stage-specific models would be preferred for estimating plant N concentration. Mid-season plant N content estimation could significantly improve the opportunity for farmers to intervene with strategic fertilizer management. Ideally, the choice of an index for canopy N measurement should not depend on the geographical location where measurements are made. The VIs that minimize the soil reflectance, such as red edge based VIs, have the best performance across different locations with different soil type. These kinds of VIs could be used to map N content across farmer fields without calibrations, allowing them to target N applications. The results mean that adding red edge band to UAV sensors can improve plant N concentration monitoring and estimation. The main concern about developed models for plant N concentration estimation is that these models are crop-specific. Each crop has its’ own unique spectral signature; thus, the same models cannot be used for various crops. Changes in plant characteristics (such as breeding improvements) may require the development of additional algorithms. Mixed results about the effect of wheat cultivars on spectral reflectance have been reported in literature. Sembiring et al [40] found that wheat varieties did not have significant effect on spectral measurements. On the other hand, Sultana et al [41] documented that spectral reflectance (NDVI) values have varied significantly for a wide range of cultivars treated with the same N rates.

Remotely sensed VIs have been extensively used to quantify wheat crop N status. The UAV technology appears to provide a good complement to the current remote sensing platforms for N monitoring in wheat by capturing low-cost, high resolution images. These UAV technologies can bring a unique perspective to N management in wheat by providing valuable information on wheat N status. Time, labor and money can be saved using UAV data in crop monitoring.

Results presented in this paper show that high resolution images acquired with UAVs are a useful data source for in-season wheat crop N concentration estimation. At Feekes 5 growth stage, red edge and green based VIs had higher correlation with plant N concentration compared to red based VIs because red edge based VIs can reduce the soil background effect on crop reflectance. At Feekes 10 growth stage, all calculated VIs showed high correlation with plant N concentration, and there were no significant differences between red and red edge based VIs’ performance. At this stage, crop canopy has been fully developed, and soil reflectance did not have strong effect on the reflectance of research plots. At Feekes 5, the plant N concentration estimated based on NDVI_{red edge} showed 1:1 correlation with N concentration measured in the lab. At Feekes 10, the estimated and measured N concentration were highly correlated for all developed models, but the model based on CI_green was the only model that had a 1:1 correlation between estimated and measured plant N concentration. The observed high correlation between UAV based VIs with plant N concentration indicates the applicability of UAV for in-season data collection from agricultural fields.

4. Conclusions

Remotely sensed VIs have been extensively used to quantify wheat crop N status. The UAV technology appears to provide a good complement to the current remote sensing platforms for N monitoring in wheat by capturing low-cost, high resolution images. These UAV technologies can bring a unique perspective to N management in wheat by providing valuable information on wheat N status. Time, labor and money can be saved using UAV data in crop monitoring.

Results presented in this paper show that high resolution images acquired with UAVs are a useful data source for in-season wheat crop N concentration estimation. At Feekes 5 growth stage, red edge and green based VIs had higher correlation with plant N concentration compared to red based VIs because red edge based VIs can reduce the soil background effect on crop reflectance. At Feekes 10 growth stage, all calculated VIs showed high correlation with plant N concentration, and there were no significant differences between red and red edge based VIs’ performance. At this stage, crop canopy has been fully developed, and soil reflectance did not have strong effect on the reflectance of research plots. At Feekes 5, the plant N concentration estimated based on NDVI_{red edge} showed 1:1 correlation with N concentration measured in the lab. At Feekes 10, the estimated and measured N concentration were highly correlated for all developed models, but the model based on CI_green was the only model that had a 1:1 correlation between estimated and measured plant N concentration. The observed high correlation between UAV based VIs with plant N concentration indicates the applicability of UAV for in-season data collection from agricultural fields.

Acknowledgements

This study was supported in part by the Idaho Wheat Commission.

Cite this paper

Walsh, O.S., Shafian, S., Marshall, J.M., Jackson, C., McClintick-Chess, J.R., Blanscet, S.M., Swoboda, K., Thompson, C., Belmont, K.M. and Walsh, W.L. (2018) Assessment of UAV Based Vegetation Indices for Nitrogen Concentration Estimation in Spring Wheat. Advances in Remote Sensing, 7, 71-90. https://doi.org/10.4236/ars.2018.72006

References